|
|
This appendix explains how to install Cisco IOS software onto "run-from-RAM" Cisco routers using a TFTP server or remote copy protocol (rcp) server application.
The information in this document describes Cisco IOS Release 11.2 or later.
Perform these steps prior to installing or upgrading Cisco IOS software:
A TFTP server or a RCP server application must be installed on a TCP/IP-ready workstation or PC. After the application is installed, a minimal level of configuration must be performed.
a. Configure the TFTP application to operate as a TFTP server, as opposed to a TFTP client.
b. Specify the outbound file directory. This is the directory in which the Cisco IOS software images are stored (see Step 2 below). Most TFTP applications provide a setup routine to assist in these configuration tasks.
Note The TFTP server included on the software feature pack CD-ROM can be used on a PC running Windows 95. For other operating system s, a number of TFTP or rcp applications are available from independent software vendors or as shareware from public sources on the World Wide Web. The TFTP Server application included on the software feature pack CDs is also available on Cisco.com.
c. Download a TFTP server for Windows 95.
Step 2 Download the Cisco IOS software image onto your workstation or PC.
You should now have a TFTP server installed, with a valid Cisco IOS software image.
 |
Note For remote copy program (rcp) applications, substitute rcp for every occurrence of TFTP. For example, use the copy rcp flash command instead of the copy tftp flash command. |
Speed 9600 bits per second 8 databits 0 parity bits 1 stop bit No Flow Control
Step 2 Verify that the TFTP server has IP connectivity to the router.
Check the IP addresses of the TFTP server and the router (access server) targeted for the TFTP software upgrade to be sure that the addresses are within the same range. Ping the router (access server) to verify that a network connection exists between them. More information on IP addresses is available in "Resolving Common Image Installation Problems."
Step 3 Copy the new software image from the TFTP server to the router (access server) using the following commands:
Router> enable Password: password Router# Router# copy tftp flash
|
Note When you are connected to the router through the console port, if you get a > or rommon > prompt, your
router is in ROM monitor (ROMMON) mode. If necessary, consult the
Boot Failure
Recovery Procedures on Cisco.com.
|
If necessary, you can copy an image from one device to another.
|
Note Cisco recommends that you keep a copy of the router or access server configuration before upgrading the router or access server software. The upgrade itself does not affect the configuration, which is stored in nonvolatile RAM (NVRAM). |
Step 4 When prompted, enter the IP address of the TFTP server as in the following example:
Address or name of remote host [255.255.255.255]? 172.17.247.195
Step 5 When prompted, enter the filename of the Cisco IOS software image to be installed, as in the following example:
Source file name? ubr7200-k8p-mz
|
Note The image name varies depending on the filename of the image on the TFTP server. |
Step 6 Specify the destination filename:
Destination file name? ubr7200-k8p-mz
This is the name the new software image will have when it is loaded onto the router. The image can be named anything, but common practice is to enter the UNIX image filename.
Step 7 Erase the Flash device before confirming:
a. Enter yes to erase the existing software image resident in the router's Flash memory before copying the new one.
b. Enter no to keep the existing software image. Be sure that you have enough Flash memory to keep both.
Erase flash device before writing? [confirm] yes/no
Step 8 Before reloading, verify the correct installation and commands.
a. Verify that the image is properly installed and that the boot system commands point to the proper file to load. Information about verifying the image and boot commands is available in "Resolving Common Image Installation Problems."
b. To reload the image, type:
Router# reload *Mar 1 00:30:49.972: %SYS-5-CONFIG_I: Configured from console by console System configuration has been modified. Save? [yes/no]: no !-- lower case Proceed with reload? [confirm] yes !-- lower case
Step 9 Use the show version command to verify that the router is running with the proper image.
Router# show flash -#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name 1 .. unknown 317FBA1B 4A0694 24 4720148 Aug 29 1997 17:49:36 hampton/nitro/c7200-j-mz 2 .. unknown 9237F3FF 92C574 11 4767328 Oct 01 1997 18:42:53 c7200-js-mz 3 .D unknown 71AB01F1 10C94E0 10 7982828 Oct 01 1997 18:48:14 rsp-jsv-mz 4 .D unknown 96DACD45 10C97E0 8 639 Oct 02 1997 12:09:17 the_time 5 .. unknown 96DACD45 10C9AE0 3 639 Oct 02 1997 12:09:32 the_time 6 .D unknown 96DACD45 10C9DE0 8 639 Oct 02 1997 12:37:01 the_time 7 .. unknown 96DACD45 10CA0E0 8 639 Oct 02 1997 12:37:13 the_time 3104544 bytes available (17473760 bytes used)
The following documents on Cisco.com contain additional information related to software installation and upgrade:
The table below provides command options for copying a system image from one device to another. Methods vary according to different platforms.
The three most common commands used for image copying are:
copy tftp flashRefer to the Cisco IOS Configuration Fundamentals Command Reference , Release 12.1 on Cisco.com.
Router# show slot0
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1 .D unknown 5E8B84E6 209D8 11 2392 Jan 22 2000 00:22:42 flashconfig
2 .. image 5E7BAE19 B623C4 22 11802988 Jan 22 2000 00:23:18 rsp-jsv-mz.1 20-8.0.2.T
Router# show slot1:
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1 .. unknown 6A2B4BA7 6FA9E0 20 7186784 Jul 30 1999 15:05:19 rsp-jv-mz.11 1-26.CC1
2 .. config 631F0D8B 6FB1EC 6 1929 Oct 19 1999 06:15:49 config
3 .. config 631F0D8B 6FB9F8 7 1929 Oct 19 1999 06:16:03 config1
Router# copy slot0: slot1
Source filename []? rsp-jsv-mz.120-8.0.2.T
Destination filename [slot1]?
CCCCCCCCCCCCCCCCCCCC
2392 bytes copied in 0.300 secs
Perform these steps in global configuration mode.
Router# show flash System flash directory: File Length Name/status 1 11173264 c2500-jos56i-l.120-9.bin [11173328 bytes used, 5603888 available, 16777216 total] 16384K bytes of processor board System flash (Read ONLY)
Step 2 Activate the TFTP server on the router that has the Cisco IOS software image that you want to copy. The example below provides the command sequence to use:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# tf Router(config)# tftp-server ? flash: Allow URL file TFTP load requests flh: Allow URL file TFTP load requests lex: Allow URL file TFTP load requests null: Allow URL file TFTP load requests nvram: Allow URL file TFTP load requests system: Allow URL file TFTP load requests Router(config)# tftp-server Router(config)# tftp-server flash:? flash:c2500-jos56i-l.120-9.bin Router(config)# tftp-server flash:c2500-jos56i-l.120-9.bin Router(config)# ^Z Router#
Step 3 After the TFTP server is configured, you can download the specified image from the router using the copy tftp flash command, as if it were a classic TFTP server.
|
Note The IP address of your TFTP server is the address of the router on which you configured the tftp-server command. |
Posted: Thu Jun 27 22:57:10 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.